During the site walkthrough, managers should identify and document the following items, since it will shape the service approach:
Managers can take everything learned during the site visit and create a site engineering plan to share with employees and executives so everyone is on the same page.
A lot is still happening on the green side in early fall, which can push preparing the winter fleet far down the to-do list. Managers need to avoid being unprepared for an early or even the first snowfall, so they can take these steps to make sure equipment is ready to roll:
Create a readiness schedule. Identify the snow season kickoff date and calculate the amount of time teams need to prepare equipment. Use that date to create a fleet maintenance timeline. Leave plenty of time to avoid having to rush to finish, knowing that current season maintenance and breakdowns might temporarily derail the schedule. If needed, start small by preparing one or two trucks with plows and spreaders now in case of an early storm and add more to the rotation as winter nears.
Order parts early. The closer managers get to the start of the season, the more likely it is that parts will be on back order. Plan to purchase parts that tend to break more often, as well as major parts, such as plow pumps and spreader motors, that might be hard to come by in the middle of a storm.
Equipment prep. Clean, repair and service winter equipment before putting it away at the end of the season. But even with proper storage, issues can still arise and should be caught early. Once autumn arrives, operators should pull out key pieces of equipment to inspect, connect and test its operation:
Trucks. Start with a thorough pressure wash and inspection and make necessary repairs. Check all electrical systems — including batteries, starters, alternators and wiring — to ensure everything is connected and in good condition. Inspect hydraulic systems for leaks or damaged hoses. Finally, change the oil and filters, and conduct a full check of all lights and connections.
Plows. To keep plows in good working order, start by flushing and replacing the hydraulic fluid and checking the cutting edges for signs of wear. Inspect and tighten all hoses, fittings and fasteners, pivots and pins. Clean the electrical connections, test the battery and charging system and verify that the plow and truck lights are functioning correctly. Finally, do a complete inspection to identify signs of mechanical damage that might need attention.
Spreaders and sprayers. Inspect and tighten all hoses, fittings, set screws and fasteners while checking for mechanical damage or chain tension issues. Clean electrical connections, lubricate all fittings and service the gearboxes. Do not forget to check the pumps on liquid applicators for leaks and inspect nozzles and spray bars for damage or blockages to confirm that the correct nozzles are properly installed and ready for service.
Don’t forget to calibrate. The easiest way to waste salt, which may be in short supply again this winter, is using spreaders and sprayers that have not been properly calibrated. Establish a consistent process, and calibrate equipment before the season starts, mid-season and whenever mechanics make equipment repairs or significant material changes. Be sure to document these settings, rates and maximum output for each site and include this information in the team's preseason training.
Training significantly reduces the risk of workplace injuries. Beyond safety, well-trained operators are less likely to cause costly property or equipment damage, saving the headache of repairs and insurance claims. It also bolsters the defense against liability and slip-and-fall claims by ensuring the team can proactively identify and mitigate hazards.
Managers can gather teams before the snow season begins to cover safety, equipment operation and standard procedures. Proactively identifying training needs allows managers to plan and schedule the training without the pressure of an impending storm.
All employees — even the most seasoned veterans — should participate in preseason training that combines classroom training with hands-on practice. Important areas to cover include personal health and safety, equipment safety and operational efficiency, yard safety and chemical safety.
Once the material has been taught, managers should put it to the test with dry runs that replicate the conditions operators will encounter on-site. For example, have crews drive their assigned routes. Walk the sites with the site engineering plan and site maps to identify potential hazards, stacking areas, priority areas and other details that are covered in the service plan. Perform a full mock run from beginning to end in the dark to test response times, routes, equipment operations and procedures. It is better to identify potential hiccups during training than in the middle of a storm.
By focusing on these critical pillars — walking the site, ensuring your equipment is field-ready and investing in comprehensive team training — managers can build a foundation for operational excellence. Taking these steps now ensures that the team is ready to deliver safe, efficient and high-quality service all winter long.
Cheryl Higley is education and content director with the Snow & Ice Management Association (SIMA). SIMA offers training programs and resources to help grounds managers and snow and ice professionals prepare for winter. Access safety training programs at sima.org/safety.